Saturday, May 16, 2020

I've got some good news and some bad

First the bad news .......

Hans Summers, G0UPL has announced the end of the QCX radio. Sine 2017, this monoband QRP radio has enjoyed quite the following, with over 9,000 units sold. And the reason for its popularity was clear. It's not every day you can buy a kit for a SUPERBLY performing radio for under $50.

The good news is that Hans has announced he's taking pre-orders for the QCX+, which will ship this June. Rather than letting me go on about it, let me post some pictures and I'll let the designer speak for himself.

First the old kit:


Out with the old and in with the new:






Now, some words from the designer himself:

Hi all,

9,937 QCX kits have been sold since the launch in August 2017. The current batch of kits are almost at an end. Despite the huge number of kits sold to date, the ongoing demand is still very strong. It became apparent to me that regardless of what other new kits come later, there will always be a place in many radio ham's hearts for a high performance, mono-band QRP CW transceiver kit. With its high performance, easy to build and use, CW decoder (including practice mode) and keyer, etc etc., the kit has also proven attractive to newcomers to amateur radio and/or CW.

But I wanted to fix some of the things that have always nagged me at the back of my mind since the start. For the YOTA 2017 summercamp hosted by RSGB in UK, I was under such tight budgetary and time constraints that I had to compromise on certain things. Particularly the inconvenience of fitting the QCX into an enclosure due to the connectors on the two sides, with controls and LCD all at different heights. This has been a distinct disadvantage in many people's mind (though also unleashing much creativity among mechanically inclined constructors).

QCX+ is the replacement for the QCX. No more QCX kits will be made. You can read about the QCX+ here http://qrp-labs.com/qcxp .

The QCX+ development is complete, it is currently in production and will be shipping in mid-June. I am making this announcement now, to allow pre-orders, since the current batch of QCX kits is now practically finished.

But:

QCX+ is the same circuit as QCX.
QCX+ runs the same firmware as QCX.
QCX+ operates just like a QCX.

The changes in QCX+ are as follows (summary, see http://qrp-labs.com/qcxp for full details):

Optional beautiful extruded aluminium enclosure
Much larger PCB. The PCB area is more than doubled. This permits a less dense component installation, following feedback from some constructors who found the QCX PCB rather densely populated. The main PCB is 13 x 10cm (compared to 8 x 10cm in QCX).
Thicker PCB traces (at least 16mil, rather than 12mil in QCX)
Traditional front-panel arrangement: vertical front panel PCB holds LCD and controls, rear horizontal PCB has the main circuits. Pin-headers connect the two.
Power on/off button on front panel
All connectors are on the rear PCB edge
Two additional 3.5mm stereo jack connectors for PTT (50W PA) and CAT control.
2.1mm barrel connector for power
7805 bolts to rear panel for heatsinking
Three BS170 PA transistors and the MPS751 keying envelope transistor are now bolted flat on the PCB for heatsinking purposes - reducing probability of overheating
Lots of pin headers and test pads for debugging, extending, experimenting, modifying etc., including modifying the purpose of the rear panel 3.5mm jack connectors
Plenty of space for modifications and experiments
C24 increased to 470uF (quieter Tx/Rx transitions in full-QSK mode)
Incorporates IC3 pin 13-14 10K resistor mod http://www.qrp-labs.com/qcx/qcxmods/ptt.html
Due to the 2.2x increase in PCB area, additional inter-board connectors, switches, hardware etc., there is a modest increase in price from $49 to $55.
The price of the optional enclosure kit is $25. The combination of QCX+ and QCX+ Enclosure is still cheaper than the combination of QCX and the most popular enclosure (BaMaTech aluminium enclosure).

Manufacturing is already underway and PRE-ORDERING is now open, for shipment in mid-June 2020. See http://shop.qrp-labs.com/qcxp

Wow! Looks good to me! I have a 40 Meter QCX, I might just be tempted to order a 20 Meter QCX+

Thanks, Hans for continuing the "Art of QRP" and favoring us with your superb design and engineering skills!

72 de Larry W2LJ
QRP - When you care to send the very least!

3 comments:

  1. Good evening Larry, WOW the comments from Hans sound very much like Elecraft. He is listening to the user and taking the feedback and putting it into a great package. Sounds like a great radio that is coming out and thank Larry for posting about it.
    73,
    Mike
    VE9KK

    ReplyDelete
  2. Perhaps the very best reason why I really should attend some CW boot camp or other. Must...try...harder.

    Lovely unit. It must be absolutley wonderful to stick that in your backpack and just do radio!

    ReplyDelete
  3. Hi Larry Got a 29Meter kit on order...Thanks for bringing it to my attention...73 de Bob KR9Z

    ReplyDelete